2017 Takeuchi TL10V2
The TL10V2 features a vertical lift loader arrangement and is Final Tier 4 emissions compliant. The cab is completely redesigned and enlarged and features a low effort overhead door design for improved entry and egress. A quiet track design with wide block tread reduces vibration, noise levels, and improves ride quality.
Features may include:
ENGINE- EPA Final Tier 4 Emission Compliant
- Turbocharged
- High Pressure Common Rail Injection System
- DOC+DPF Exhaust After Treatment
- Automatic Fuel Bleed System
- Active Power Control Power Management System
- Working Modes - Power and ECO
- Dual Element Air Filter
- High Capacity Radiator and Hydraulic Oil Cooler Mounted Side-by-Side on Swing Out Frame
- 5.7" Color Multi-Informational Display with Rear Camera
- Sealed Rocker Switches
- 12 volt System with 60 amp Alternator
- LED: Two Front and Two Rear
- Engine Preheat
- Hour Meter
- Back-up Alarm
- Horn
- Double Planetary Reduction Drives
- Permanently Sealed Track Rollers with Metal Face Seals
- Fully Welded Frame with Integrated Cross Members
- 2 Speed Travel
- 15.7" Rubber Track
- Grease Type Track Adjuster
- Front and Rear Tie-Down Points and Lift Points
- Rear Bumper Integrated into Frame
- Tilt-up Operator's Station
- Deluxe High Back Suspension Seat
- Rear View Camera
- Foot Throttle
- Dial Throttle Control
- Rear Pivoting Lap Bar with Arm Rest
- ROPS / FOPS Structure
- Retractable 2" Seat Belt
- Vertical Lift Design
- Pilot Hydraulic Controls
- Boom Float with Detent
- Cushioned Boom Cylinders
- Hydraulic Self Leveling
- Proportional Auxiliary Hydraulic Controls with Detent
- Pressure Relieving Flat Faced Coupler Body
- 14-Pin Connector with Push Button Control
- High Capacity Steel Hydraulic Tank
- Mechanical Quick Coupler
- Hydraulic Quick Coupler Cab - Standard Equipment
- 2017
- Takeuchi
- TL10V2
- Base
- Compact
- Raise-Full Load: 4.3 Seconds | Lower-No Load: 3.0 Seconds | Dump-Full Load: 3.1 Seconds | Curl-No Load: 2.2 Seconds
- Kubota / V3307CR-TE4B
- EPA Final Tier 4
- 4/203 cu in (3.3 L)
- 74.3 hp (55.4 kW)
- 2,600 rpm
- 195 ft-lb @ 1,500 rpm (265 Nm)
- 11.8 qt (11.2 L)
- 15.9 qt (15.0 L)
- (65% of full load): 2.7 gal/hr (10.3 L/hr)
- Spring Applied, Hydraulically Released
- System: 12 volts / 60 amps
- Tipping Load: 7,205 lb (3,270 kg) | Operating Load at 50% of Tipping Load: 3,600 lb (1,635 kg) | Bucket Breakout Force: 6,520 lb (2,960 kg) | Lift Arm Breakout Force: 5,400 lb (2,450 kg) | Traction Force: 9,730 lb (4,410 kg)
- Low: 4.8 mph (7.7 km/hr) | High: 7.0 mph (11.3 km/hr)
- Canopy: 4.9 psi (34.3 kPa) | Cab: 5.1 psi (35.4 kPa)
- Reservoir: 9.5 gal (36.0 L) | System: 17.2 gal (65.0 L)
- Auxiliary - Primary Circuit: 18.8 gpm (71.2 Lpm)
- System Operating: 3,481 psi (24 MPa)
- Front Clearance Radius without Bucket: 5 ft 0 in (1,535 mm) | Rear Clearance Radius: 5 ft 5.2 in (1,655 mm) | Angle of Departure: 30 degrees | Dump Height Fully Raised: 7 ft 11.9 in (2,435 mm) | Maximum Dump Angle Fully Raised 40.0 degrees | Maximum Bucket Rollback at Ground Level: 30 degrees | Reach Fully Raised: 3 ft 1.4 in (950 mm)
- 15.7 in (400 mm)
- Track Ground Contact: 4 ft 7.9 in (1,419 mm)
- Maximum to Bucket Pin: 10 ft 4.8 in (3,170 mm)
- Without bucket: 5 ft 8.5 in (1,740 mm)
- 7 ft 5.4 in (2,270 mm)
- Without Bucket: 12 ft 1.0 in (3,680 mm)
- Minimum: 12.6 in (320 mm)
- 21.5 gal (81.0 L)
- Rated Operating, SAE J818: 2,522 lb (1,144 kg)
- Operating Canopy: 9,810 lb (4,450 kg) | Cab: 10,130 lb (4,585 kg)
- Traction Drive Type: Hydrostatic drive with double reduction planetary final drive | Track Roller Type: Permanently sealed rollers with precision metal face seals | Track Rollers: 5 per side
- 410000371
- $32,865.00
- Spokane Valley
- Pre-Owned
- SID-24576
- 2017
- Takeuchi
- TL10V2
- 410000371
- 1812
- Available
- 410000371